IR Detecting Units for Remote Control
 
(Ta = 25°C)
Type Series No. Absolute maximum ratings Operating
voltage
(V)
Electrical characteristics Size (mm) Terminal
layout
Vcc (V) Topr (°C) Icc
(mA)*1
MAX.
VOH
(V)
MIN.
VOL
(V)
MAX.
fo
(kHz)
TYP.
With shield case (holder), 5 V drive GP1UM26XK0VF 0 to 6.0 −10 to +70 4.5 to 5.5 0.6 (0.65) Vcc–0.5 0.45 *3 5.6 × 9.6 × 6.8 Center
Vcc
GP1UM27XK0VF 0 to 6.0 −10 to +70 4.5 to 5.5 0.6 (0.65) Vcc–0.5 0.45 *3 5.6 × 9.6 × 12.0
GP1UM28XK0VF 0 to 6.0 −10 to +70 4.5 to 5.5 0.6 (0.65) Vcc–0.5 0.45 *3 5.6 × 9.6 × 16.0
GP1UM28YK0VF 0 to 6.0 −10 to +70 4.5 to 5.5 0.6 (0.65) Vcc–0.5 0.45 *3 5.6 × 8.6 ×
12.5(9.6)*2
With shield case (holder), 5 V drive, Strengthened resistance to
electromagnetic induction
noise
GP1UM26RK0VF 0 to 6.0 −10 to +70 4.5 to 5.5 0.6 (0.65) Vcc–0.5 0.45 *3 5.6 × 9.6 × 7.2
GP1UM27RK0VF 0 to 6.0 −10 to +70 4.5 to 5.5 0.6 (0.65) Vcc–0.5 0.45 *3 5.6 × 9.6 × 12.4
GP1UM28RK0VF 0 to 6.0 −10 to +70 4.5 to 5.5 0.6 (0.65) Vcc–0.5 0.45 *3 5.6 × 9.6 × 16.4
GP1UM28QK0VF 0 to 6.0 −10 to +70 4.5 to 5.5 0.6 (0.65) Vcc–0.5 0.45 *3 5.6 × 9.0 ×
12.5(9.6)*2
GP1UM29QK0VF 0 to 6.0 −10 to +70 4.5 to 5.5 0.6 (0.65) Vcc–0.5 0.45 *3 5.6 × 16.2 ×
21.9(19)*2
With shield case (holder), 3 to 5 V drive GP1UE26XK0VF 0 to 6.0 −10 to +70 2.7 to 5.5 0.4 Vcc–0.5 0.45 *3 5.6 × 9.6 × 6.8
GP1UE27XK0VF 0 to 6.0 −10 to +70 2.7 to 5.5 0.4 Vcc–0.5 0.45 *3 5.6 × 9.6 × 12.0
GP1UE28XK0VF 0 to 6.0 −10 to +70 2.7 to 5.5 0.4 Vcc–0.5 0.45 *3 5.6 × 9.6 × 16.0
GP1UE28YK0VF 0 to 6.0 −10 to +70 2.7 to 5.5 0.4 Vcc–0.5 0.45 *3 5.6 × 8.6 ×
12.5(9.6)*2
With shield case (holder), 3 to 5 V drive, Strengthened resistance to
electromagnetic induction
noise
GP1UE26RK0VF 0 to 6.0 −10 to +70 2.7 to 5.5 0.4 Vcc–0.5 0.45 *3 5.6 × 9.6 × 7.2
GP1UE27RK0VF 0 to 6.0 −10 to +70 2.7 to 5.5 0.4 Vcc–0.5 0.45 *3 5.6 × 9.6 × 12.4
GP1UE28RK0VF 0 to 6.0 −10 to +70 2.7 to 5.5 0.4 Vcc–0.5 0.45 *3 5.6 × 9.6 × 16.4
GP1UE28QK0VF 0 to 6.0 −10 to +70 2.7 to 5.5 0.4 Vcc–0.5 0.45 *3 5.6 × 9.0 ×
12.5(9.6)*2
GP1UE29QK0VF 0 to 6.0 −10 to +70 2.7 to 5.5 0.4 Vcc–0.5 0.45 *3 5.6 × 16.2 ×
21.9(19)*2
Holderless, 5 V drive, Strengthened resistance to
electromagnetic induction
noise
GP1UX51QS 0 to 6.0 −10 to +70 4.5 to 5.5 0.6 Vcc–0.5 0.45 *3 5.5 × 5.3 × 7.5 Center
GND
GP1UX51RK 0 to 6.0 −10 to +70 4.5 to 5.5 0.6 Vcc–0.5 0.45 *3 5.5 × 5.3 × 7.5
Holderless, 3 to 5 V drive, Strengthened resistance to
electromagnetic induction
noise
GP1UX31QS 0 to 6.0 −10 to +70 4.5 to 5.5 0.4 Vcc–0.5 0.45 *3 5.5 × 5.3 × 7.5
GP1UX31RK 0 to 6.0 −10 to +70 4.5 to 5.5 0.4 Vcc–0.5 0.45 *3 5.5 × 5.3 × 7.5
Note: A voltage regulator circuit is built-in but may be affected by the usage environment. Install with an externally mounted C and R as a power supply filter.
*1 When no signal is input (during input light).
*2 Figures in parentheses indicate the distance to the light detection center.
*3 fo = 32.75/36/36.7/38/40 kHz
※Notice
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP devices shown in catalogs, data books, etc. Except where specially indicated, models listed on this page comply with the RoHS Directive*. For details, please contact SHARP.
*RoHS Directive: Prohibits use of lead, cadmium, hexavalent chromium, mercury and specific brominated flame retardants (PBBs and PBDEs), with certain exceptions.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.